MOXA MGate 5109 Series
1-port Modbus RTU/ASCII/TCP-to-DNP3 serial/TCP/UDP gateways
- Supports Modbus master/slave and DNP3 master/outstation
- Up to 31 Modbus serial slaves or DNP3 serial outstations
- Up to 32 Modbus TCP slaves or DNP3 TCP/UDP outstations
- Supports DNP 3.0 subset level 2
- DNP3 master mode supports up to 26600 points
- DNP3 master and outstation modes support time-synchronization
- Complete diagnosis information for maintenance
- Embedded Modbus and DNP3 serial traffic monitor
- Redundant dual DC power inputs and relay output
- microSD card for configuration backup and system log
- -40 to 75°C wide operating temperature models available
- Serial port with 2 kV built-in isolation protection
- Built-in Ethernet cascading for easy wiring
The MGate 5109 is an industrial Ethernet gateway for Modbus RTU/ASCII/TCP and DNP3 serial/TCP/UDP protocol conversion. All models are protected with a rugged metallic casing, are DIN-rail mountable, and offer built-in serial isolation. The MGate 5109 supports transparent mode for easily integrating Modbus TCP to Modbus RTU/ASCII networks or DNP3 TCP/UDP to DNP3 serial networks.The MGate 5109 series gateways support Modbus and DNP3 Protocol Traffic Monitor for easy troubleshooting, especially during the installation stage. Communication issues could be caused by incorrect software parameters, such as slave ID and register address, 5109 also support agent mode to exchange data between Modbus and DNP3 networks or to act as a data concentrator for multiple Modbus slaves or multiple DNP3 outstations. The rugged design is suitable for industrial applications such as power, oil & gas, and water and wastewater.
Easy Configuration via Web Console
The MGate 5109 series comes with an illustrated Quick Setup guide designed to make configuration easy. With Quick Setup, you can easily access protocol conversion modes and finish the configuration in a few steps. The MGate 5109 series also supports Auto Detection for DNP3 serial outstations, allowing the MGate 5109 to automatically acquire all outstation objects when configured as a DNP3 master.
Modbus and DNP3 Protocol Traffic Monitor
The MGate 5109 series gateways support Modbus and DNP3 Protocol Traffic Monitor for easy troubleshooting, especially during the installation stage. Communication issues could be caused by incorrect software parameters, such as slave ID and register address, or incorrect command configuration. With Modbus/DNP3 Protocol Traffic Monitor, you can check the captured data and easily identify the root cause.
Variety of Maintenance Functions
The MGate 5109 series gateway provides a web console and Telnet console for remote maintenance. Encryption communication functions, including HTTPS and SSH, are supported to provide better network security. In addition, firmware log functions are provided to record connection events and Modbus maintenance events. Users can review log data remotely through the web console.
Easy Configuration via Web Console
The MGate 5109 series comes with an illustrated Quick Setup guide designed to make configuration easy. With Quick Setup, you can easily access protocol conversion modes and finish the configuration in a few steps. The MGate 5109 series also supports Auto Detection for DNP3 serial outstations, allowing the MGate 5109 to automatically acquire all outstation objects when configured as a DNP3 master.
Modbus and DNP3 Protocol Traffic Monitor
The MGate 5109 series gateways support Modbus and DNP3 Protocol Traffic Monitor for easy troubleshooting, especially during the installation stage. Communication issues could be caused by incorrect software parameters, such as slave ID and register address, or incorrect command configuration. With Modbus/DNP3 Protocol Traffic Monitor, you can check the captured data and easily identify the root cause.
Variety of Maintenance Functions
The MGate 5109 series gateway provides a web console and Telnet console for remote maintenance. Encryption communication functions, including HTTPS and SSH, are supported to provide better network security. In addition, firmware log functions are provided to record connection events and Modbus maintenance events. Users can review log data remotely through the web console.
Ethernet Interface
- Protocols
Modbus TCP client/server, DNP 3.0 TCP/UDP master/outstation
Number of Ports
2 (1 IP, Ethernet cascade)
Speed
10/100 Mbps, Auto MDI/MDIX
Connector
8-pin RJ45
Magnetic Isolation Protection
1.5 kV (built-in)
Serial Interface
- Protocols
Modbus RTU/ASCII Master/Slave
Number of Ports
1
Serial Standards
RS-232/422/485, software selectable
Connectors
DB9 male
RS-485 Data Direction Control
ADDC® (automatic data direction control)
Pull High/Low Resistor for RS-485
1 kÙ, 150 kÙ
Terminator for RS-485
120 Ù
Isolation
2 kV (built-in)
Serial Communication Parameters
- Data Bits
7, 8
Stop Bits
1, 2
Parity
None, Even, Odd, Space, Mark
Flow Control
RTS/CTS, RTS Toggle (RS-232 only)
Baudrate
50 bps to 921.6 kbps
Serial Signals
- RS-232
TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422
Tx+, Tx-, Rx+, Rx-, GND
RS-485-4w
Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w
Data+, Data-, GND
Modbus
- Functions Supported
1, 2, 3, 4, 5, 6, 15, 16, 23
Max. No. of Commands
100
Max. No. of Connections
MGate as Modbus TCP Master: 32 slave connections
MGate as Modbus TCP slave: 16 master connections
DNP3
- Max. No. of Connections
- Transparent mode:
16 master connections or 32 outstation connections - Agent mode:
MGate as DNP3 TCP/UDP master: 32 outstation connections
MGate as DNP3 TCP/UDP outstation: 1 master connection - For each outstation:
Binary Inputs: 256 points
Analog Inputs: 64 points
Counters: 64 points
Binary Outputs: 256 points
Analog Outputs: 64 points - When the MGate 5109 is configured as a DNP3 outstation Bina
DNP3 Internal Database
Software
- Configuration Options
Web Console, Serial Console Utility
Configuration
MXview, SNMP (v1, v2, v3), Private
Physical Characteristics
- Housing
Metal, IP30
Weight
507 g (1.12 lb)
Dimensions
36 x 105 x 140 mm (1.42 x 4.14 x 5.51 in)
Storage Card Slot
1 microSD (SDHC) card slot supports up to 32 GB
Relay Alarm Circuit
3-pin circuit with current carrying capacity of 2 A @ 30 VDC
Environmental Limits
- Operating Temperature
Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity
5 to 95% (non-condensing)
Vibration
IEC 60068-2-6, IEC 60068-2-64
Shock
IEC 60068-2-27
Drop
IEC 60068-2-32
Power Requirements
- Input Voltage
12 to 48 VDC
Input Current
455 mA @ 12 VDC; 125 mA @ 48 VDC
Power Connector
Terminal block
Standards and Certifications
- Safety
UL 508, EN 60950-1
Hazardous Location
Class 1 Division 2, ATEX, IECEx
EMC
EN 55022/24
EMI
CISPR 22, FCC Part 15B Class B
EMS
IEC 61000-4-2 ESD: Contact: 8 kV; Air: 15 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 10 V/m
IEC 61000-4-4 EFT: Power: 4 kV; Signal: 2 kV
IEC 61000-4-5 Surge: Power: 2 kV; Signal: 2 kV
IEC 61000-4-6 CS: 150 kHz to 80 MHz: 10 V/m
IEC 61000-4-8 PFMF
MTBF (mean time between failures)
- Time
859,422 hrs
Standard
Telcordia SR332
ORDERING INFORMATION | |
Available Models | |
MGate 5109 | 1-port Modbus-to-DNP3 gateway, 0 to 60°C operating temperature |
MGate 5109-T | 1-port Modbus-to-DNP3 gateway, -40 to 75°C operating temperature |
Optional Accessories
| |
DR-4524 | 45W/2A DIN-Rail 24 VDC power supply with universal 85 to 264 VAC or 120-370 VDC input, -10 to 50°C operating temperature |
DR-75-24 | 75W/3.2A DIN-Rail 24 VDC power supply with universal 85 to 264 VAC or 120-370 VDC input, -10 to 60°C operating temperature |
DR-120-24 | 120W/5A DIN-Rail 24 VDC power supply with universal 88 to 132 VAC or 176 to 264 VAC input by switch, or 248-370 VDC , -10 to 60°C operating temperature |
| |
Mini DB9F-to-TB | DB9 Female to Terminal Block connector |
Customers who viewed this item also viewed