S-CONNECT - Advantech BB-WDR-120 Series

Single and two phase wide input range 180 ~ 550VAC
Protections: Short circuit / Overload / Over voltage / Over temperature
Cooling by free air convection
Built-in constant current limiting circuit
Can be installed on DIN rail TS-35/7.5 or 15
UL508(industrial control equipment)approved
EN61000-6-2(EN50082-2) industrial immunity level
100% full load burn-in test
Built-in DC OK relay contact

120W, Single Output, Industrial DIN Rail Power Supply

SPECIFICATIONS

MODEL	BB-WDR-120-12	BB-WDR-120-24
OUTPUT
DC VOLTAGE	12V	24V
RATED CURRENT	10A	5A
CURRENT RANGE	0 ~ 10A	0 ~ 5A
RATED POWER	120W	120W
RIPPLE & NOISE (max.) Note.2	120mVp-p	120mVp-p
VOLTAGE ADJ. RANGE	12 ~ 15V	24 ~ 29V
VOLTAGE TOLERANCE Note.3	± 1.5%	± 1.0%
LINE REGULATION	± 0.5%	± 0.5%
LOAD REGULATION	± 0.5%	± 0.5%
SETUP, RISE, HOLD UP TIME	2000ms, 70ms, 50ms/400VAC 2000ms, 70ms, 10ms/230VAC at full load
INPUT
VOLTAGE RANGE	180 ~ 550VAC 254 ~ 780VDC
FREQUENCY RANGE	47 ~ 63Hz
EFFICIENCY (Typ.)	89.5% / 400V	91% / 400V
AC CURRENT	0.7A/400VAC 1.2A/230VAC
INRUSH CURRENT (max.)	COLD START 50A
LEAKAGE CURRENT	<3.5mA / 530VAC
PROTECTION
OVERLOAD	105 ~ 130% rated output power
	Protection type : Constant current limiting, recovers automatically after fault condition is removed
OVER VOLTAGE	16 ~ 18V	31 ~ 37V
	Protection type : Shut down o/p voltage, re-power on to recover
OVER TEMPERATURE	Shut down o/p voltage, recovers automatically after temperature goes down
FUNCTION
DC OK SIGNAL	Relay contact rating(max.) : 30V / 1A resistive
ENVIRONMENT
WORKING TEMP.	-25 ~ +70 °C (Refer to "Derating Curve")
WORKING HUMIDITY	20 ~ 90% RH non-condensing
STORAGE TEMP., HUMIDITY	-40 ~ +85 °C, 10 ~ 95% RH
TEMP. COEFFICIENT	± 0.03%/ °C (0 ~ 50°C)
VIBRATION	Component: 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting clip: Compliance to IEC60068-2-6
SAFETY & EMC (Note 4)
SAFETY STANDARDS	Ul508 approved, IEC60950-1 CB approved by SIQ, design refer to GL;(meet EN60204-1)
WITHSTAND VOLTAGE	I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC O/P-DC OK:0.5KVAC
ISOLATION RESISTANCE	I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 °C/ 70% RH
EMC EMISSION	Compliance to EN55011 (CISPR11), EN55032 (CISPR32), EN61204-3 Class B
EMC IMMUNITY	Compliance to EN61000-4-2,3,4,5,6,8,11, EN61204-3, EN61000-6-2 (EN50082-2), heavy industry level, criteria A
OTHERS
MTBF	268K hrs min. MIL-HDBK-217F (25 °C)
DIMENSION	40125.2113.5mm (WHD)
PACKING	0.65Kg; 20pcs/14Kg/1.16CUFT
NOTE
1. All parameters NOT specially mentioned are measured at 400VAC input, rated load and 25 °C of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Length of set up time is measured at cold first start. Turning ON/OFF the power supply very quick may lead to increase of the set up time.

ORDERING INFORMATION

Available Modules
BB-WDR-120-12	PS, DIN, WIDE VOLTAGE INPUT, 120W, 12V
BB-WDR-120-24	120W, 24V, 10A, Single Output, Industrial DIN Rail Power Supply

Advantech BB-WDR-120 Series Datasheet (372.4 kB)