S-CONNECT - Advantech BB-WDR-240-24

Single and two phase 180~550VAC wide input range
High efficiency 91% and low power dissipation
Protections: Short-circuit, Overload, Over-voltage, Over-temperature
Free air convection cooling
DIN rail TS-35/7.5 or 15 mountable
UL508 approved (industrial control equipment)
EN61000-6-2 (EN50082-2) industrial immunity level
Built-in DC OK relay contact
100% full-load burn-in test

240W, 24V, 10A, Single Output, Industrial DIN Rail Power Supply

SPECIFICATIONS

MODEL	BB-WDR-240-24
OUTPUT
DC VOLTAGE	24V
RATED CURRENT	10A
CURRENT RANGE	0 ~ 10A
RATED POWER	240W
RIPPLE & NOISE (max.) Note.2	150 mVp-p
VOLTAGE ADJ. RANGE	24 ~ 28V
VOLTAGE TOLERANCE Note.3	± 1.0%
LINE REGULATION	± 0.5%
LOAD REGULATION	± 1.0%
SETUP, RISE TIME	800ms, 150ms/400VAC 1500ms, 150ms/230VAC at full load
HOLD UP TIME (Typ.)	18ms / 400VAC 18ms / 230VAC at full load
INPUT
VOLTAGE RANGE	180 ~ 550VAC 254 ~ 780VDC
FREQUENCY RANGE	47 ~ 63Hz
POWER FACTOR (Typ.)	PF≥0.84/400VAC PF≥0.84/230VAC
EFFICIENCY (Typ.)	91% / 400V
AC CURRENT	1A/400VAC 2A/230VAC
INRUSH CURRENT (max.)	COLD START 50A
LEAKAGE CURRENT	<3.5mA / 530VAC
PROTECTION
OVERLOAD	105 ~ 130% rated output power
OVERLOAD	Protection type : Constant current limiting, unit will shut down after 3 sec. , auto-recovery after 1 minute if the fault condition is removed
OVER VOLTAGE	29 ~ 33V
OVER VOLTAGE	Protection type : Shut down o/p voltage, auto-recovery after 1 minute if the fault condition is removed
OVER TEMPERATURE	90°C ± 5°C (TSW) detect on heatsink of power switch
OVER TEMPERATURE	Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
FUNCTION
DC OK SIGNAL	60Vdc/0.3A, 30Vdc/1A, 30Vac/0.5A resistive load
ENVIRONMENT
WORKING TEMP.	-30 ~ +70 °C (Refer to "Derating Curve")
WORKING HUMIDITY	20 ~ 95% RH non-condensing
STORAGE TEMP., HUMIDITY	-40 ~ +85 °C, 10 ~ 95% RH
TEMP. COEFFICIENT	± 0.03%/ °C (0 ~ 50°C)
VIBRATION	Component: 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting clip: Compliance to IEC60068-2-6
SAFETY & EMC (Note 4)
SAFETY STANDARDS	Ul508 approved, IEC60950-1 CB approved by SIQ, design refer to GL;(meet EN60204-1)
WITHSTAND VOLTAGE	I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC O/P-DC OK:0.5KVAC
ISOLATION RESISTANCE	I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC / 25 °C/ 70% RH
EMC EMISSION	Compliance to EN55032 (CISPR32), EN61204-3 Class B, EN61000-3-2,-3
EMC IMMUNITY	Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2 (EN50082-2), EN61204-3, heavy industry level, criteria A approved
OTHERS
MTBF	141.1K hrs min MIL-HDBK-217F (25 °C)
DIMENSION	63125.2113.5mm (WHD)
PACKING	1.06Kg; 12pcs/13.7Kg/1.06CUFT
NOTE
1. All parameters NOT specially mentioned are measured at 400VAC input, rated load and 25 °C of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Installation clearances : 40mmon the top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power. In Case the adjacent device is a heat source, 15mm clearance is recommended. 6. Derating may be needed under low input voltage. Please check the derating curve for more details.

Advantech BB-WDR-240-24 Datasheet (819.9 kB)